Mudroom Coat rack Bench

Hi all! I know, it’s been a LONG time since I put together a blog post, and I apologize….life is just nutty sometimes and I needed a break…..I’m sure you know what I mean.  :0)

I thought you all might like to see a project I did a few months ago that I absolutely LOVE! It’s a mudroom coat rack/bench. You remember the old 1916 house that was torn down?  The one I took the old bank of drawers from to make my window seat? Well, I salvaged quite a few old doors from there as well. I decided this would be a fun way to use those doors! Here’s what I made!….

It looks a lot more complicated than it was, I promise!  :0)

My doors were 48” wide when butted up against each other, but you can see in the pic they have little strips of wood on each side that ended up making them 49”. I wanted to keep the hinges, but didn’t really want to see anything but the pretty part, so I used that trim to cover them up.  (more on that later)

To make the base I purchased a 4 x 8 sheet of MDF (medium density fiberboard) and three 8’ long 2 x 4’s.  (the 4 x 8 sheets are actually 49” wide)
I cut two of the 2 x 4’s to 49” long and then cut three pieces 15” long….two for the ends and one for a center brace. My finished piece is 18” deep, the standard depth for a bench. I used some wood glue and my nail gun to nail it all together.  I then cut a top for my base piece..again, 49” wide x 18” deep.

See how my side pieces are on the INSIDE of my two longer outer pieces. You want to build it like this for strength.

I made sure to check the fit of the MDF piece by laying it on top of the base and checking on all sides, this will become your bottom piece to your actual bench. (where the little baskets slide in)  Don’t attach this to the base yet.

To build the actual bench part of the unit, I cut one more 49” x 18” piece of MDF  for the top piece of the bench, and two pieces for the sides that were 18” deep x 14” high.  I also cut two pieces that will be used for the center braces, and they were 18” deep x 13” high.

You assemble your bench like below using wood glue and a nail gun.

I cut a scrap piece of trim to 15 1/4” and used it to make sure my brace pieces where exactly the same distance apart from each other, like this….

and this……

then I used wood glue and my nail gun to assemble it together.

I drew a line across the top where I was going to be nailing into the braces underneath, so I knew where to nail. I didn’t want to split out the piece of MDF bracing….

Then it was easy to just follow along that line and nail without worrying about splitting out my braces…

After it was all glued and assembled, I attached it to the 2 x 4 base I had built earlier with glue and my nail gun.

Then I trimmed it out with some baseboard molding I had laying around the garage….

Next I moved onto the doors. I basically laid them out flat on two saw horses and gave them a good sanding.

After they were thoroughly sanded, I used mending plates to attach them together on the back where it would never be seen.  I forgot to take a picture of this part, but basically this is a mending plate, and you just lay it across the two doors and screw it in to make the two doors as one.

Next I moved onto the shelving unit at the top of the piece. I had some extra lumber from other projects, and I used it to make the shelving part.  I cut a piece of pine lumber 49” long x 5” wide. It’s the piece that will lay flat against the doors. (it’s the piece laying flat on the carpet in the pic) The top piece is MDF, and I cut it 49” long x 9” deep. It sits on top of the other piece and is glued and screwed from the top. I used screws on this piece cause you’re never going to see the top and I wanted it to be extra sturdy. I didn’t attach the corbels to the shelf at this point because I attached the shelf to the doors with screws under where the corbels are sitting so you won’t see the screws.

Before I attached the shelf to the doors, I installed some pieces of wood to the sides of my doors to hide where the hinges will go.    It was 1/2” thick x the depth of my door, which happened to be 1 3/4” thick.  I used wood glue and my nail gun to attach those pieces.  I took the hinges apart, and only used the pretty part with the rounded brass tops, and pounded them down into the openings. I only did it on the two top openings, because the bottom holes will be covered by the bench.

Sorry, I got a little lazy about taking pictures and forgot to show you under the corbels where I screwed them to the doors. I’m sure you can envision the shelf screwed on under the corbels.  I then used the existing holes that came in my corbels to screw those to the doors and upper shelf. I filled them with wood filler and sanded it off.  (you can see the wood filler on the fronts of the corbels if you look closely) You can also see in this picture, that I trimmed the shelf out with some trim I also had on hand.  What I don’t show in this pic, but you can see in the final pics, is that I added some crown molding between each corbel.

At this point, I trimmed out the bench around the top, and also down the front of the brace pieces with some trim. I was also a little antsy and couldn’t wait to see how my baskets were going to look. I got those adorable baskets at Walmart! They are from the Better Homes and Gardens collection and were only $9.97 each! I’m showing you in this picture how I’ll be pushing the bench up against the doors…….I couldn’t attach mine until I got it in the house because it would’ve been too big to go in my front door.  (it looks like it’s not the same width in this picture, but it really is..it’s just where I still had it pulled out in the floor a little bit)

Here it is inside the house and all screwed together. I basically pushed the bench up against the doors, and pre-drilled from the back into the 2 x 4’s I built the bases out of and used REALLY long screws to screw it into place. I also used some L brackets and attached it on the inside top of the bench where you can’t see it, and screwed them into the doors and inside the back of the bench.

Then I pretty much just added a couple of hooks for coats etc, and primed and painted! (oh and you can see the pieces of crown molding between the corbels that I was talking about earlier…I just glued and nailed that into place)

I did add a tufted bench top later on. I used another 49” x 18” piece of MDF and just screwed it to the existing bench top after I tufted it.  I have tutorial on how to diamond tuft in my post on how to diamond tuft a chair. You can just use some screws and washers instead of a needle and thread….see…

Then you just use a covered button kit (I used 7/8”) to cover up the screws…

See….just lovely!

And there ya have it…a Coat rack/ bench/ mudroom all rolled up into one!

 

 

You can see I left the old glass door knobs and hardware on the doors…I just thought it added to the authenticity of the doors. (as long as you don’t sit in the middle of the bench, they don’t get in the way of you leaning back either) :0)  hee hee hee

So there ya have it…how to make a cute mudroom/bench out of old doors!

Hope you enjoyed my project!

Blessings

Missy

How to Change Your Doorbell Button

Please tell me I’m not the only one with such a pitiful looking little doorbell button as this.  It was hanging on by one little screw.  It’s been like that since we bought the house SIX years ago!! (yes, I know…sad.)  On a whim we decided to replace it Saturday…..Yay…a very GOOD whim indeed! :0)

We took a little trip to Lowes and found a pretty Oil Rubbed Bronze doorbell button.  It was a little more than the rest, but after six years of living with the ugly one, $16.00 didn’t sound too bad.  It also lights up!

We also picked up a 1/8” masonry bit.  You have to buy a bit a little smaller around than your screws.

In the first picture, you can see my hubby is unscrewing that one little lone screw that’s held our doorbell button on for all this time. BEFORE you unscrew anything make SURE YOUR POWER IS TURNED OFF!  I had my hubby stand outside and continuously ring the bell until I found the right breaker than turned it off. I was lucky and got it on the first try!  When you take the screws out of your doorbell and take it off, you will have little wires attached to two screws on the back.

Unscrew each of the screws on the back, and remove the wires from around the screws.

You’ll be left with two wires sticking out of your wall.  We had two extra wires, I’m really not sure what they’re for, but they weren’t connected to our old button, so we didn’t worry with them. :0)

We didn’t realize until after we opened the doorbell we bought, that it had to be recessed in the wall, so my hubby chipped away the mortar with an old masonry bit and hammer until it was deep enough for the new doorbell to sit back into.

We then held the new doorbell button up and marked where the screws had to go, then drilled holes the depth of the screws that came with the button.

Loosen the screws on the back of your doorbell, and then wrap the bare part of each wire, around each of the screws and tighten them up. 

Here we are tightening the screws.  There weren’t any real clear instructions on which of the two wires went to which screw, but it said you’ll know if its right if the doorbell rings. If not, switch the wires around.  Wow…crazy instructions!

Here’s what ours looked like after we had the wires hooked up. (by the way, we got the wires right on the first try…no re-wiring!) :0)

Here is our doorbell being recessed back into the wall….

Then just screw the screws into the pre-drilled holes.

Isn’t is lovely?!  So much better!!

Here’s my honey trying out the new button!

And I bet you’ll never guess where this button is now…..yep, I trashed it! :0)

This was probably one of the easiest projects we’ve ever done….guess we should have done is SIX YEARS AGO!! ;0)

Blessings,
Missy

Disclaimer: I am in no way an electrician, this is just how we installed our doorbell, so I can’t be responsible for any differences in how yours might be hooked up. :0) Good Luck!

Technorati Tags: how to replace your doorbell,replacing your doorbell button,how do I replace my doorbell

Who Doesn’t LOVE New Pillows!!

Hey you guys!! It has been crazy around here, that’s why I haven’t posted in a bit. My hubby had his gall bladder removed and I’ve been playing nurse maid.  He’s still feeling a little rough, but I’m sure he’ll be feeling better real soon! :0)

Ok, so you all know I love the pillows I made when I built my window seat, but after the photo shoot, I decided I wanted to change it up a little bit, so I went pillow shopping! (gosh, what a chore!)

Here are my new pillows! I LOVE the pillows I made, but I wanted some colors for fall, and all these pillows are so cute!! :0)

I found all of these pillows at TJ Maxx….my FAVORITE store in the world! (well them and Lowes….it might be a tie!)

The big square striped pillows are actually pillow shams, but I liked the colors and stripes, so I got them. I put a pillow down inside and used the ties on the back as a design element, then I just flipped the excess towards the back.

I love all the warm colors and fun patterns of all the pillows! Do you know you can mix all kinds of patterns of fabrics as long as the scales are different. For instance, you can have a large scale plaid, a small floral, an embroidered piece, and stripes, all together. I love to mix patterns, textures and colors!

I ADORE the HOME pillow!! I was in the store, and I grabbed it like someone was standing there behind me ready to pounce on my treasure. :0)

Then there’s this pillow.  To look at it, it’s not really me, but something about it drew me in…I think it’s my love of silhouettes, so here it is. The more it’s in my dining room, the more I like it.
:0)

I really like how full and fluffy all these pillows are…and OH so comfy! Oh, and I got them just in time for snuggling up with a certain magazine and cup of hot chocolate! Gee, I wonder what magazine that would be! ;0)

Have a great day!

Missy

Technorati Tags: how to build a window seat,window seat pillows,this old house magazine photo shoot,How to decorate a window seat,how to mix fabric patterns

Garden Shed Twist

I’m trying to get back to reality after my This Old House Magazine cover fun, so I thought I’d show you the “twist” to my garden shed we had built this summer!
Are you ready?
Here’s our garden shed the way it was the last time I showed it to you….

Well, I made a bit of an addition to my shed, and it all started because of these………….

Nope, not the topiaries, but the side light windows on each side of my door.  When we had someone come to our door and knock, they could very easily see into our house….I  just wasn’t comfortable with that! So we happened to be walking through Lowes one day and saw these…..REPLACEMENT SIDE LIGHTS!

They are the perfect way to add instant charm to your home and also keep people from seeing in.  They are glass, but the only part that is completely clear is the little beveled pieces that make up the pretty part of the stained glass.   They were really easy to install too…there’s complete instructions inside the box, but honestly, all you do is unscrew the old ones, pop them out, clean up the area a little, and pop these in and screw them back together.  It was probably the easiest project we’ve ever done in our house!  Now it looks like this….

Cute huh?! I love them, and I really love the fact that people can’t see into our house anymore!

OK…now back to the shed! Ya’ll know how I LOVE to repurpose things right?  Well I had these two perfectly adorable clear sidelights that we had removed, so there was no way I was gonna throw them away.  You already know what I’m going to say don’t you?!  Yep, I installed them in the shed! (a friend of mine came over to help me…it was a two person job for sure)

You wanna see?! Ok, here she is all painted with a pretty color called Cappacino, with her new sidelight windows!….

Don’t those little side windows just make it the most charming little garden shed ever?! I thought I loved my little shed before, but I LOVE it even more since we installed the sidelights! OH…and check out the adorable handles I put on!  I found them at Tuesday Morning for $2.99 each!  I have some more plans for my cute little shed, like maybe a little porch out front, and some landscaping,  but they’ll have to wait a while…lots of other projects I’m working on for now.

What do you think? :0)

Blessings
Missy

Technorati Tags: garden shed,cute garden sheds,side lights,garden shed ideas